> >

Blank Stair下载

Blank Stair

Blank Stair

5229 人安装 0 人喜欢 0 人评论

Blank Stair 截图

Blank Stair Blank Stair Blank Stair Blank Stair

Blank Stair 描述

Blank Stair takes all the work out of calculating a set of steps.
This is two apps built into one. You get a staircase calculator and also a balluster spacing calculator.
STAIRCASE:
Enter overall height of the staircase and you will get:
* Overall width of the staircase
* Number of treads
* Riser height
* Tread run
* Staircase angle
* Staircase dimensions: the rise and run of each tread.
!* Running stringer points.
BALLUSTERS:
Enter the width of the opening (plus a few details about your ballusters and layout) and you get:
* Balluster count
* Spacing
* Layout position of each balluster
Answers are in INCHES-SIXTEENTHS format (i.e. 4-7 is 4 and 7/16"). That means no converting decimals to fractions on the jobsite.
It is FREE. Try it and love it.
QUICK TUTORIAL
STAIRCASE:
1. Run the app and click the STAIRCASE button.
2. Enter the overall staircase height. This is the height from the finished floor at the bottom to the finished floor at the top.
Risers:
3. EITHER enter an acceptable range for the riser height OR the number of treads desired for the steps. If you specify a range, the riser height will be close to the middle of the range. If you enter the number of treads, the range values are ignored.
4. Check or uncheck the 'Start One Step Down' checkmark. Most steps start 'One Step Down' from the top.
5. Enter the thickness of your treads.
6. Enter the width of the treads.
7. Enter the desired amount of overhang for each tread.
8. Click 'Calculate'
The next screen will give you the information about your stairs. Most of the infor is self-explanatory.
If you cut steps the old-fashioned way, just use the rise and run cut values from this page to mark your stringers.
However, a far superior method of marking stringers is to use the Running Stringer Layout. Here is a quick guide:
* Starting at the end of the board, make a mark at each point in the chart.
* Put your stop clamps on your framing square at the rise/run marks.
* For each tread, find the best place to fit the square between each set of marks. In a perfect world, the square will fit perfectly between each set of marks.
* Continue up the stringer, marking each tread, until all are marked.
Using this method eliminates marking errors. Nearly perfect stairs every time.
BALLUSTERS:
1. Run the app and click the BALLUSTERS button.
2. Enter the overall width of the opening.
Balluster width:
3. Enter the thinest part of the balluster. Often times, stair spindles vary in thcknness. measure along the balluster to find the thinnest part.
4. Enter the width of the balluster at the top/bottom. If (very unlikely) you have a balluster that is thicker in the middle than it is at the top/bottom, enter the thickness at the top.
5. Enter the maximum allowable spacing allowed between ballusters. Usually, this is 4 inches.
6. Check or uncheck weather you want the results to be 'On Center' or 'On Edge' layout.
7. Click 'Calculate'
The next screen will give you the information about your balluster layout.
TIP: If you are installing ballusters between several openings that are next to each other (like a deck rail), you should try to get the spacing between the ballusters in each section to match the spacing in the other sections. Here's how:
* Calculate the spacing for each section. Write them down.
* Usually there will be several sections that are either identical or very close. Settle on the most common spacing.
* Then, on the sections that do not match closely enough, adjust the 'Max Spacing' field and then recalculate that section. You may have to do this a couple of times in order to get the best spacing to match the other sections. It is OK if sections varys a bit from one another section. Minor variations are invisible to the eye.
Carpentry Carpenter Construction Contractor Guard Stair Balcony Wood Woodworking Bannister Spindles Pickets Handrail
空白楼梯通吃的工作计算出来的一套步骤。
这是一种建立在一个两个应用程序。你得到一个楼梯计算器,也是一个balluster间隔计算器。
楼梯:
进入楼梯的整体高度,你会得到:
 *楼梯总宽度
 *胎面数
 *提升高度
 *轮距运行
 *楼梯角
 *楼梯尺寸:每个胎面的崛起和运行。
!*运行纵梁点。
BALLUSTERS:
进入开口的宽度(加上你的ballusters和布局的一些细节),你会得到:
 * Balluster计数
 *间距
 *布局每个balluster位置
答案是英寸十六分之格式(即4-7是4和7/16“)。这意味着没有转换为小数的现场分数。
它是免费的。试试吧,喜欢它。
快速教程
楼梯:
1.运行应用程序,并单击楼梯按钮。
2.输入整个楼梯的高度。这是从成品地板的高度在底部到成品地板上方。
立管:
3.任何输入可接受范围为提升管高度或期望的步骤胎面的数目。如果指定的范围内时,提升管高度将接近该范围的中间。如果输入胎面的数量,范围值将被忽略。
4.选中或取消选中“启动一个降压'对号。最开始的步骤,从顶部的“一降压”。
5.输入您的胎面厚度。
6.输入胎面的宽度。
7.输入每个胎面突出端的所需量。
8.单击“计算”
下一个屏幕将让你对自己的楼梯的信息。大部分的Infor的是不言自明的。
如果你削减步骤老式的方法,只要使用的兴起和运行切值从该页面,以纪念您纵梁。
然而,标记纵梁的远远优于方法是使用运行纵梁布局。这里是一个快速指南:
 *启动在董事会结束,做一个标记在图表中的每个点。
 *把你的止损夹上的上升/运行标记您的取景广场。
 *对于每一个花纹,找到适合每一套标记之间的广场上最好的地方。在一个完美的世界里,广场将完全适合每一组标记之间。
 *继续向上纵梁,标记每个胎面,直到所有标记。
使用这种方法消除了标记的错误。近乎完美的楼梯每一次。
BALLUSTERS:
1.运行应用程序,然后单击BALLUSTERS按钮。
2.输入口的总宽度。
Balluster宽度:
3.输入balluster的最薄的部分。很多时候,楼梯纱锭thcknness有所不同。沿balluster测量找到最薄的部分。
4.输入在顶部/底部的balluster的宽度。如果(非常不可能)你有balluster即在中间厚于它是在顶部/底部,进入位于顶部的厚度。
5.输入ballusters之间所允许的最大允许间距。通常,这是4英寸。
6.选中或取消选中的天气,你想要的结果是“在中心”或“在边缘”的布局。
7.点击“计算”
下一个屏幕将让你对自己balluster布局的信息。
提示:如果要安装几个开口是彼此相邻(如甲板铁路)之间ballusters,你应该尝试让ballusters之间的间距在每个部分的间距相匹配的其他部分。具体方法如下:
 *计算的间隔为每个部分。把它们写下来。
 *通常会有几个部分是相同的或非常接近。解决上最常见的间距。
 *然后,对不符合不够紧密的部分,调整“最大间距”字段,然后重新计算部分。可能必须要这样做几次,以获得最佳的间距相匹配的其它部分。这是确定的,如果部分瓦里斯有点相互部分。轻微的变化是看不见的眼睛。
木工木匠施工单位卫队楼梯阳台木木工班尼斯特主轴纠察队扶手

Blank Stair 更新内容

9/30/11 Minor change in Market file.
9/14/11 Minor enhancements.

Blank Stair 历史版本

Blank Stair 使用技巧

Blank Stair 应用内最新内容

Blank Stair 信息

大小
25.19K
分类
系统工具
TAG
更新
版本
1.1
要求
Android 1.6 以上
来自
Google Play

下载Blank Stair的人还下载

应用下载排行榜

  1. 微信 5.8 亿人安装 下载
  2. QQ 6.1 亿人安装 下载
  3. UC浏览器 2.5 亿人安装 下载
  4. 搜狗输入法 5.9 亿人安装 下载
  5. 阿里星球 9315 万人安装 下载
  6. QQ空间 4.3 亿人安装 下载
  7. 淘宝 5.3 亿人安装 下载
  8. 墨迹天气 8705 万人安装 下载
  9. 微博 2.3 亿人安装 下载
  10. 酷狗音乐 2.3 亿人安装 下载
豌豆荚安卓版二维码

扫一扫安装
豌豆荚安卓客户端