IMPORTANT NOTE:
IN SOME RARE CASES THE APPLICATION CAN MAKE THE WI-FI ON SOME DEVICES STOP WORKING, NOT BEING ABLE TO CONNECT EVEN TO INFRASTRUCTURE NETWORKS. DON'T WORRY, IT'S FIXABLE. JUST FOLLOW THE STEPS AT THIS POST:
http://www.slatedroid.com/topic/16005-zt-180-adhoc-switcher/page__st__60__p__204274#entry204274
WARNING:
This application is intended to be used with devices having an RT2870, RT3070 or Texas Instrument Wi-Fi module, although it has only been tested with the Zenithink ZT-180 tablet with Android 2.1 and 2.2 OS versions.
It should work with other devices using one of these Wi-Fi modules or with other OS versions, or even might work with devices using other Wi-Fi modules on "just to try..." mode, as for example the iMX515 tablet with Atheros module (thanks to Miguel Minglas for his help on testing), but that's not sure and it's something you try at your own risk. According to received comments, in addition to ZT-180 the application worked on the following devices: iMX515, Samsung Galaxy Tab P1010 and FlyTouch 2.
IF YOUR DEVICE IS NOT A ZT-180 OR ONE OF THE DEVICES REPORTED AS COMPATIBLE AND THE APPLICATION DOESN'T WORK, THEN DON'T GIVE A BAD RATING. PLEASE, IN SUCH CASE USE THE SEND REPORT OPTION OFFERED BY THE APPLICATION.
----------------------
ZT-180 Adhoc Switcher is an utility created to easily apply/restore the 'TxPower' (for some devices only) mod and to switch the Wi-Fi connection between the default infrastructure mode, which allows the connection to routers or access points, and the ad-hoc mode, which allows the connection to another Wi-Fi device, such a phone which is sharing its Internet connection (tethering).
For this application to work properly it needs a 'rooted' device.
NOTES:
- Sometimes the application may take a while to start, showing a blank screen; please wait.
- Before to switch to ad-hoc mode, remember to go to settings and set the SSID which your phone's tether application uses and, if necessary, the WEP key.
- Sometimes the ad-hoc connection may take a while or may not be made at first attempt; please wait 30 seconds or even 1 minute and if the connection is not at least attempted ("trying to connect to..." status) then disable and re-enable Wi-Fi; if the connection is attempted but is not successful then revise the SSID and WEP key on settings.
- The "refresh Wi-Fi on system boot" option causes Wi-Fi to be turned off and then turned on again at boot time, but only if the previous Wi-Fi state was enabled and there is no active connection after boot; if Wi-Fi was disabled when the device was powered off or rebooted then it will remain disabled at boot, or if device succeeded to establish a connection at boot by itself then the refresh will be omitted to keep that connection. This option may be useful on some situations when a device has problems to automatically connect at boot, although the Wi-Fi is on, but it can connect fine if the Wi-Fi is turned off and on again.
重要提示:
在某些罕见的情况下,应用程序可以在Wi-Fi在某些设备停止工作,不能够连接连基础设施网络。不要担心,这可以解决的。只要按照以下步骤中的这篇文章:
http://www.slatedroid.com/topic/16005-zt-180-adhoc-switcher/page__st__60__p__204274#entry204274
警告:
此应用程序旨在与具有RT2870,RT3070或德州仪器的Wi-Fi模块的设备使用,虽然它只有经过测试与卓尼斯ZT-180平板电脑采用Android 2.1和2.2版本的操作系统。
它应该使用其中的一个无线网络连接模块或与其他版本的操作系统,甚至是其他设备的工作可能会使用其他Wi-Fi模块的“只是尝试...”模式的设备工作,例如在iMX515平板电脑Atheros的模块(感谢米格尔Minglas为他的测试帮助),但是这不能肯定,它的尝试风险自负东西。根据收到的意见,除了ZT-180的应用程序工作在以下设备:iMX515,三星Galaxy Tab P1010和飞触2。
如果你的设备是不是一个ZT-180或报告为兼容的设备,并应用程序不工作,那么不给差评。请,在这种情况下使用发送报告选项OFFERED应用程序。
----------------------
ZT-180即席切换器是创建轻松应用/恢复“TXPOWER”(仅适用于某些设备),MOD和切换默认的基础架构模式之间的Wi-Fi连接,它允许连接到路由器或接入点的工具,并在ad-hoc模式,它允许连接到另一个无线网络连接装置,例如一个电话被共享其因特网连接(圈养)。
对于这个应用程序能够正常工作,它需要一个'扎根'设备。
注意:
- 有时,应用程序可能需要一段时间才能启动,显示一个空白的屏幕;请耐心等待。
- 在切换到ad-hoc模式,记得去设置,并设置该手机的系绳应用程序使用的SSID,如果有必要,WEP密钥。
- 有时Ad hoc连接可能需要一段时间,或可能不会在第一次尝试作出;请等待30秒甚至1分钟,如果没有至少尝试连接(“试图连接到...”状态),然后禁用和重新启用Wi-Fi;如果尝试连接,但没有成功,然后在修改设置SSID和WEP密钥。
- “刷新无线网络连接在系统启动”选项使无线网络被关闭,然后再次打开在启动时,但只有当先前的Wi-Fi状态启用并没有开机后没有活动连接;如果当设备被关闭或Wi-Fi被禁用,然后重新启动它仍将在启动禁用,或者如果设备成功建立在引导本身的连接,然后刷新将被省略,以保持这种连接。当一个设备有问题,自动连接,在开机,虽然Wi-Fi的是,此选项可能在某些情况下非常有用,但它可以连接正常,如果Wi-Fi已关闭,再次打开。
ZT-180 Adhoc Switcher更新内容
v1.4c (07/06/2011)
- added new data and other adjustments to the report which can be generated when the application is not working; sorry but some data was not being correctly reported
网友评论更多